Determining the Anchor Point

Waterpooling will cause extra stress on the shade sail and your mounting surfaces. So it's recommended to install your shade sail with a tilt of at least 40 degree to allow water to drain. There are several different ways you can tilt your shade sail

Secure the correct angle between mounting point and sail corners: make sure your shade sail are based on the continuity of the diagonals and not the sides. This will help create even tension and a flat sun shade surface

Take the sun into consideration. Think about what time of day you'll usually be enjoying your outdoor space and where you want the shade to be located for a more effective installation

Measuring the Shade Sails

Make sure you are measuring from mounting point to mounting point, and not just measuring the area on the ground. It might help to determine and note down the height of each of your mounting points from the ground up, especially if you wish to anchor the shade sail onto walls.

Different shaped shade sail requires different measurements to be taken
• Triangular: 3 sides
• Rectangular: 4 sides & two diagonal

We recommend measuring from anchor point to anchor point. Based on the numbers you provide we'll deduct 20 inches on the either the longest side or the longer diagonal (depending on which shade sail it is - specified on product page) while maintaining the shape to ensure a stable attachment, proper tension and minimize sagging.

If you wish to cover a large area try combining several pieces of shade sails together.

Installing the Shade Sails

1. Place pad eye onto the determined mounting point and mark the four holes.

2. Use the corresponding sized drill bit to drill into marked points and insert expansion inserts a. (e.g. M6 requires 6-mm diameter drill bit)

3. Place pad eye back on and secure with nails

4. Install snap hook or adjustable turnbuckles as needed and make sure the tension of the shade sail surface is correctly distributed. The shade sail should be flat and evenly stretched out in all directions.

Ensure the mounting point direction is a continuation on the diagonal of the shade sail surface for even tension distribution.

Make sure the shade sails are installed at least 40 degree angle so that water can drain smoothly to prevent pooling

All corners of the shade sail need to be fully stretched out and evenly distributed

Apart from hardware installation kit and ropes we also offer support pole and ring clip that can be used to secure shade sails
• The pole is secured at the base with four pieces of expansion nails
• Install the ring buckle where you wish the mounting point to be and use with snap hook or turnbuckles to secure your shade.

Häufig gestellte Fragen

Mess- und Installationsanleitung für Sonnensegel

Soll das Sonnensegel den exakten Abstand zwischen den Ankerpunkten einhalten?

Nein . Sie sollten das Sonnensegel etwas kleiner als den Ankerabstand wählen, um Platz für Spannvorrichtungen (Spannschlösser, D-Ringe, Kabel) zu lassen. Die auf unserer Produktseite angegebene fertige Segelgröße (Bestellgröße) ist die fertige Produktgröße (Details zur Größenreduzierung finden Sie in der Anleitung auf jeder Produktseite oder in der Maßanleitung für Sonnensegel), nicht der gerade Abstand zwischen den Ankern.

Welche Neigung bzw. welchen Winkel benötige ich bei der Installation?

Das Segel muss mit einer Mindestneigung von etwa 30°–40° (eine oder zwei Ecken niedriger als die anderen) installiert werden, damit das Wasser ungehindert abfließen kann und sich keine Pfützen bilden, die den Stoff und die Beschläge belasten würden.

Wie werden die Beschläge richtig montiert und das Segel gespannt?

* Befestigen Sie zuerst die Ösen (Montageplatten) an Ihren Ankerpunkten, markieren und bohren Sie Löcher, setzen Sie Spreizdübel ein und befestigen Sie dann die Ösen.

* Befestigen Sie dann Karabinerhaken oder verstellbare Spannschlösser und spannen Sie das Segel so, dass es in alle Richtungen flach und gleichmäßig liegt (verwenden Sie zur Ausrichtung die Diagonalen des Segels und nicht die Seiten).