There are significant risks if you don’t know how to hang a heavy curtain rod or double curtain rod in drywall. If it’s done improperly, you’ll run the risk of needing to patch up some holes, and your curtain rod may sag, which ruins the appearance. This blog will help you learn how to install curtain rods in drywall. Even if you have drywall in your home, you’re more than entitled to spruce up those walls and give your home some nice window treatments.
Things You Will Need To Hang Curtain Rods In Drywall
Since drywall can be fairly tricky when it comes to the whole installation process for curtain rods or heavy curtains, it’s important to start by getting to the bottom of what you’re going to need. This list will help you out.
- Hammer
- 1 ¼ inch screws
- Plastic screw anchors
- 1/4-inch bit
- Pencil
- Drill
- Tape measure
You’re most likely going to need all of these, and it’s going to make the installation process much easier as well.
1. Use Longer Screws Or Nails
While there are a variety of techniques available, what ultimately matters is the size of the curtain rod set screw. You can’t do much unless you know the screw size for the curtain rod. So, the first step when hanging curtains or blinds is to determine the type of curtain rod screws, and also consider using a stud detector.
You’re going to want a stud behind the wall; otherwise, you may be at risk of the curtains tearing the plaster. Usually, it’s brackets that hold up curtain rods. To prevent sagging or tearing of the plaster, ensure the screw curtain rod set is inspected. Long nails or screws will be the best way to secure this.
How To Screw a Curtain Rod Into a Wall?
If you’re still wondering about the odds and ends of how to screw a curtain rod into the wall, then here are the steps that you’re going to need to know:
1) Begin by taking measurements, mark with a pencil to denote the end of the curtain rod
2) Measure the distance between the mounting brackets and the curtain rod
3) Remove the brackets and drill a ¼-inch hole on each mark
4) No. 8 plastic anchor screw should then be inserted; they need to fit snug, so a hammer may be required
5) Mount both brackets and ensure that they’re both secure
6) Use a measuring tape to find the center of the rod
Just take your time with this process; you’re going to need to perfect it.
2. Add Wall Anchors
Drywall anchors for curtain rods can be one of the most effective ways to ensure that your curtain rod stays secure. Indeed, one of the best ways to attach brackets to a stud behind the plasterboard is to ensure that a heavy curtain rod and curtains are completely secure and in place. However, it’s not always possible to manage this. This is where curtain rod anchors come into play.
Wall anchor curtain rod are available at most hardware stores. They come in a variety of shapes and materials, so you’re going to have plenty to choose from. Once you’ve attached your first anchor, you’re going to want to double-check the position of it. Make sure that everything is nicely aligned. Afterwards, you can easily place the end of the rod inside the bracket, hold the other end against it, and mark where you want it.
Do I Need Anchors For Curtain Rods?
While it’s not necessary, there may be times when it will be required. In cases where there aren’t any studs or you can’t install studs within the plasterboard, anchors can be used.
How To Install Wall Anchors For Curtain Rods?
When it comes to installing curtain rods with anchors, the process is fairly similar to other ways to install on drywall. So there isn’t a need for concern on how to install wall anchors for curtain rods.
For starters, ensure you’re using wall anchors capable of holding the combined weight of your curtain rod and curtains. The combined weight is absolutely important, and you can’t skip that. After installing the first anchor, make sure to double-check the position that it's in. The second one will need to align perfectly. Make sure to utilize a measuring tape and a pencil for this.
3. Install Additional Brackets
Last, but certainly not least, you’ll learn how to install curtain rod brackets. If you’re able to attach curtain rods to a stud, then adding a center support bracket is another way to stabilize the heavy window treatments.
This will also prevent sagging. In general, figuring out how to hang curtain rod brackets is fairly simple. Also, you can’t forget that curtain rods typically require a support bracket for every 25 to 35 inches. So, if you have a window that exceeds 6 feet in length, you’re more likely to need an additional bracket to support it.
